Two running steps can have the same maximum vertical ground-reaction force while one remains supported by the ground longer. The peak reveals only a single height. Impulse, by contrast, summarises force’s effect over time by accounting for the entire selected interval. You do not need complicated biomechanics software to understand it; a few clearly named forces and times suffice.
The following original calculations deliberately imagine simple, level, steady and approximately symmetrical running. They do not provide targets for your contact time or replace actual force measurements. They help you recognise what the area under a graph means, why time and force matter together, and why vertical ground force must be distinguished from the resultant force acting on the body.
Impulse belongs to the whole selected curve interval
Force impulse is force summed over time. For a constant force, it is simple multiplication: force × time. For varying force, it is the area under the force–time curve. The OpenStax university-physics explanation derives the same relationship alongside the connection between impulse and change in momentum. The unit is the newton-second, N·s; this is different from N/s, which describes force changing over time.
An original first example: an imagined force averages 1000 newtons for 0.20 seconds. Its impulse is 200 N·s. If the curve bends higher and lower but retains the same average over the same time, area and impulse can remain unchanged. One peak value therefore cannot tell you the area. You would also need the curve’s shape and the interval examined.
This distinction matters on a running report too. Vertical peak force, loading rate and vertical impulse are three separate metrics. Peak shows a maximum, rate describes a rising characteristic and impulse expresses force summed over time. Looking at how long support lasts asks a different question from examining the slope of a short interval after landing.
Several peaks can accompany the same area
Take three deliberately idealised curves, each lasting 0.20 seconds with an area of 200 N·s. The first is a rectangle 1000 newtons high. The second is a triangle starting at zero, rising linearly to 2000 newtons and returning to zero. The third is a smooth half-sine wave; the same area requires a peak of approximately 1571 newtons. Peaks therefore differ considerably despite identical duration and area.
The rectangle’s abrupt vertical edges do not represent a realistic running step. These three shapes are illustrations, not actual measurements. We chose simple forms precisely to show that area under a curve alone does not imply one unique peak. A real curve is more complex, but the principle remains. A maximum and a value summed over time do not replace one another.
Consider the reverse question too. If two triangular curves both peak at 2000 newtons but one lasts 0.20 seconds and the other 0.25 seconds, their areas are 200 and 250 N·s respectively. The same maximum can therefore accompany different impulses. Contact time and the curve’s time base are valuable information alongside the peak in a report.
Enlarge imageFirst consider the average vertical balance of the whole step
In our simple model, the runner neither rises continuously higher nor sinks continuously lower. Vertical velocity returns to the same state at the beginning and end of successive equivalent step periods. This means the resultant impulse of all vertical forces over each complete period is zero. Weight acts downwards throughout, while the ground supplies upward force only during contact.
If total step frequency is f, one step lasts 1/f. Weight force is m × g, so its downward impulse over the step period is m × g/f. Under the stated assumptions, an equal upward ground-reaction-force impulse is needed for vertical balance. Here f counts steps from both feet, not complete cycles of one foot. Confusing the definition would create a factor-of-two difference.
An original numerical example: at 70 kilograms, gravitational acceleration of 9.81 m/s² and 3 steps per second, weight force is 686.7 newtons and step time approximately 0.333 seconds. In the simple model, vertical ground-reaction-force impulse per step is 686.7/3 = 228.9 N·s. Three steps per second equals 180 steps per minute. These are original illustrative inputs, not ideal running metrics.
From contact time to average support force: dividing the same area
Keep the impulse at 228.9 N·s. With contact lasting 0.22 seconds, average vertical ground-reaction force during contact is 228.9/0.22, approximately 1040 newtons. Changing contact time to 0.20 seconds in the same simple model gives an average of 1144.5 newtons. The required area is produced in less time. We still do not know the actual peak; that would also require the curve’s shape.
| Our model | Contact time | Impulse per step | Average force during contact |
|---|---|---|---|
| A | 0.22 s | 228.9 N·s | approx. 1040 N |
| B | 0.20 s | 228.9 N·s | 1144.5 N |
The conclusion is conditional: it holds in the model with identical mass, identical step frequency and the vertical balance described. In an actual runner, changes in contact time may accompany changes in frequency, movement curve or speed. Do not read the table as saying a particular technique instruction changes someone’s measured force by exactly this amount.
The body-weight-normalised average follows directly as 1/(f × contact time). The product 3 × 0.22 is 0.66; its reciprocal is approximately 1.52. In this model, that is the ratio of average vertical ground force during contact to weight force. It is not the average over the entire step period: the ground provides no support while airborne. Always name the averaging interval.
Ground-force impulse is not the same as resultant-force impulse
During the 0.22-second stance, both the ground and weight act on the body. In our example, upward ground-force impulse is 228.9 N·s, while downward weight-force impulse during stance is 686.7 × 0.22 = 151.1 N·s. The difference is approximately 77.8 N·s upwards. This is the resultant vertical impulse during stance in the simple model assuming no other vertical external force.
Dividing by seventy kilograms gives a vertical velocity change of approximately 1.11 m/s during stance. We have not said that take-off velocity is exactly 1.11 m/s. The change is the difference between the beginning and end of stance. If something switches from downward to upward motion, for example, the difference between the two signed velocities may exceed the magnitude of either value. Without the initial state, this alone cannot calculate the final state.
During the following flight phase, weight again changes vertical velocity downwards. Of the model’s approximately 0.333-second step, 0.22 is stance, leaving about 0.113 for flight. Over that time, acceleration of 9.81 m/s² produces approximately 1.11 m/s of downward velocity change. The two parts restore the cycle’s balance. This does not make the whole movement constant in height: the body may move up and down within it.
Frequency and stance time: two numbers describe the temporal structure together
Increasing step frequency means more steps occur over the same total time. In the previous balance model, vertical ground-force impulse per step then falls. This does not automatically mean a lower peak, because contact time may shorten too. The impulse must again be distributed over a different duration. Calculate changes in both metrics together instead of looking only at the supposedly favourable direction of frequency.
When naming duty factor, pay particular attention to the denominator. One foot’s contact time is often expressed relative to that foot’s complete cycle time; f × contact time above instead uses total step frequency from both feet. In symmetrical running, a factor of two therefore separates these expressions. Both can be meaningful for the appropriate task, but giving them the same name would produce misleading numbers.
Patoz and colleagues, in fifteen trained runners, examined changes in step frequency and duty factor at a fixed speed. The results suggested partial independent adjustment within a functional range, while more extreme settings interacted. Actual movement is therefore not a single switch. Model equations help explain relationships between variables; the actual runner’s response needs separate observation.
Enlarge imageA mechanical relationship does not establish optimal technique
Jenny and Jenny’s analytical running model also describes mechanical relationships from contact time, frequency and other inputs. It assumes a simplified vertical force profile and approximately constant running speed. Its value is showing how variables may connect. A mechanical result derived from an equation is not, however, a person’s directly measured oxygen consumption.
In Moore and colleagues’ contact-time intervention study, the ten trained runners showed an individual curved relationship between metabolic cost and contact time. Measured speed and step frequency were fixed during comparisons. This research does not support the simple aim of always making contact time as short as possible. Force distribution over time and energy demand are different questions.
We did not calculate injury risk or training instructions from our examples either. A higher average external force does not directly imply stress in a particular tendon or bone. Body position, moment arms, muscle effects and further models or measurements would also matter. The aim here is interpreting data: understand why a curve’s area, average or maximum changed.
How to read your next force-measurement report
First clarify the period: does it cover one foot’s entire contact, a whole running cycle or only part of stance? Then identify the force integrated. Total vertical ground-force area differs from the resultant after subtracting weight force over the same time. Both can be useful, but answer different mechanical questions. Direction and reference therefore belong alongside the word ‘impulse’.
- Area: which force curve was summed, and between which start and end points?
- Time: contact time, step time or the cycle time of the same foot?
- Unit: N·s, or a version normalised to body weight or mass?
- Task: level, constant-speed running, or acceleration, uphill running or a bend?
Running is much more than a few arithmetic formulas, yet they help us read a graph sensibly. Peak shows a maximum; impulse shows force summed over time. Add contact time and frequency to both, and you can also ask about the step’s temporal structure. Data then become an understandable description of a precisely defined movement situation rather than an isolated score.
Sources
- OpenStax: impulse, average force and change in momentum.
- Jenny and Jenny: an analytical model of mechanical power demand in running.
- Moore and colleagues: contact time and metabolic cost.
- Patoz and colleagues: experimental changes to frequency and duty factor.
How Futószív articles are prepared: our editorial guidelines.


